eNet radio dimming actuator, 1-gang mini
Description
Intended use
- Switching and dimming of incandescent lamps, HV halogen lamps, electronic transformers for halogen or LED lamps, dimmable inductive transformers for halogen or LED lamps, HV LED or compact fluorescent lamps
- Operation with suitable eNet radio transmitters
- Mounting in appliance box according to DIN 49073 in combination with a suitable cover
- Mounting in surface-mounted housing or mounting adapter (ref.-no. FM-EBG) for false ceilings
Product characteristics
- Switch-on via bulb-preserving soft start
- Switch-on brightness can be saved permanently
- Minimum brightness can be saved permanently
- Scene operation possible
- Status indication with LED
- Status feedback to radio transmitter
- Switchable with Prog button
- Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
- Electronic over-temperature protection
- Automatic or manual setting of the dimming principle suitable for the load
- Power extension possible by means of power boosters (ref.-no. ULZ 1755 REG)
- Optional accessory: compensation module LED, ref.-no.: KM LED 230 U /ul>
- Maximum brightness
- Dimming speed
- Switch-on delay / switch-off delay
- Dim up/dim down ramp
- Switch-off warning
- Operating locks
- Continuous on, Continuous off
- Hotel function
- Run-on time /ul>
- Fully-encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
- Update of the device software
- Repeater function
- Reading of error memory /ul>
Can be set with eNet server:
Supplementary functions with eNet server:
Technical Details
Specification
Rated voltage: AC 230 V ~, 50/60 Hz
Power loss: max. 1.5 W
Stand-by power: max. 0.5 W
Ambient temperature: _25 ... +70 C
Connected load at 45 C
Power specifications including transformer power dissipation.
Operate inductive transformers with at least 85 % nominal load.
For ohmic-inductive mixed load, maximum 50 % proportion of ohmic load. Otherwise incorrect calibration of the dimmer may result.
Incandescent lamps: 20 ... 250 W
HV halogen lamps: 20 ... 250 W
Electronic transformers: 20 ... 250 W
Electronic transformers with LV LED: typical 20 ... 100 W
Inductive transformers: 20 ... 250 VA
Inductive transformers with LV LED: typical 20 ... 100 VA
Dimmable HV LED lamps: typical 3 ... 70 W
If the operating mode is set to HV LED trailing edge phase control, the maximum connected load for LED lamps increases to typ. 200 W.
Dimmable compact fluorescent lamps: typical 3 ... 70 W
Ohmic-inductive: 20 ... 250 VA
Ohmic-capacitive: 20 ... 250 W
Capacitive-inductive: not permitted
Ohmic and HV LED: typical 3 ... 70 W
Ohmic and CFL: typical 3 ... 70 W
Reduction of load for every 5 C exceeding 45 C: _5 %
for installation into wooden or hollow walls: _15 %
for installation into multiple combinations: _20 %
Amplifiers: see instructions for amplifier
Connection mode: screw terminals
- single wire: 0.75 ... 4 mm_
- stranded with ferrule: 0.75 ... 2.5 mm_
Contact type: _
Total length power cable: max. 100 m
Dimensions ( x H): 53 x 28 mm
Radio frequency: 868.0 ... 868.6 MHz
Transmitting power: max. 20 mW
Transmission range in free field: typical 100 m
Receiver category: 2
Properties
Properties
| Technology | Wireless Control |
| Brand | JUNG |
