eNet radio dimming actuator, 1-gang
Description
Intended use
- Switching and dimming of incandescent lamps, HV halogen lamps, electronic transformers for halogen or LED lamps, dimmable inductive transformers for halogen or LED lamps, HV LED or compact fluorescent lamps
- Operation with power supply (ref.-no. NT 1220 REG VDC) and receiver module (ref.-no. FM FK 32 REG) or eNet server
- Operation with suitable eNet radio transmitters
- Installation in distribution boxes on DIN rail according to EN 60715
Product characteristics
- Switch-on via bulb-preserving soft start
- Switch-on brightness can be saved permanently
- Minimum brightness can be saved permanently
- Scene operation possible
- Status indication with LED
- Status feedback to radio transmitter
- Switchable with Prog button
- Electronic short-circuit protection with permanent switch-off after 7 seconds at the latest
- Electronic over-temperature protection
- Automatic or manual setting of the dimming principle suitable for the load
- Power extension possible by means of power boosters (ref.-no. ULZ 1755 REG)
- Optional accessory: compensation module LED, ref.-no.: KM LED 230 U
Can be set with eNet server:
- Maximum brightness
- Dimming speed
- Switch-on delay / switch-off delay
- Dim up/dim down ramp
- Switch-off warning
- Operating locks
- Continuous on, Continuous off
- Hotel function
- Run-on time
Supplementary functions with eNet server:
- Fully-encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
- Update of the device software
- Reading of error memory
Technical Details
Specification
Rated voltage: AC 230 V ~, 50/60 Hz
Power loss: max. 4 W
Stand-by power: max. 0.3 W
Ambient temperature: _5 ... +45 C
Connected load at 35 C
Power specifications including transformer power dissipation.
Operate inductive transformers with at least 85 % nominal load.
For ohmic-inductive mixed load, maximum 50 % proportion of ohmic load. Otherwise incorrect calibration of the dimmer may result.
Incandescent lamps: 20 ... 500 W
HV halogen lamps: 20 ... 500 W
Electronic transformers: 20 ... 500 W
Electronic transformers with LV LED: typical 20 ... 100 W
Inductive transformers: 20 ... 500 VA
Inductive transformers with LV LED: typical 20 ... 100 VA
Dimmable HV LED lamps: typical 3 ... 100 W
Dimmable compact fluorescent lamps: typical 3 ... 100 W
With setting "LED trailing edge phase control" the max. connection power for HV LED lamps and electronic transformers with LV LED doubles.
Ohmic-inductive: 20 ... 500 VA
Ohmic-capacitive: 20 ... 500 VA
Capacitive-inductive: not permitted
Ohmic and HV LED: typical 3 ... 100 W
Ohmic and CFL: typical 3 ... 100 W
Reduction of load for every 5 C exceeding 35 C: _5 %
Amplifiers: see instructions for amplifier
Connection, outputs
- Connection mode: screw terminals
- single wire: 1.5 ... 4 mm_
- stranded without ferrule: 0.75 ... 4 mm_
- stranded with ferrule: 0.5 ... 2.5 mm_
Contact type: _
Length of output cable, per channel: max. 100 m
Mounting width: 36 mm (2 rail units)
Bus line
- Rated voltage: DC 12 V SELV
- Current consumption: 10 mA
- Connection bus: terminal
- Cable length: max. 3 m
Properties
Properties
| Technology | Wireless Control |
| Brand | JUNG |
| Mounting | DIN Rail |
| Mounting Width | 2MW |
